Enz-All is a powdered enzyme pre-spray incorporating proteolytic enzymes specifically formulated for the removal of the toughest protein greases, oils, and soils typically found in food service, hospitality, healthcare, and the home.
For use on all protein related stains –
Effectively removes blood, vomit, grass, and food stains from carpet. Spray onto the carpet, work in, and extract. Enz-All has also been found to be extremely effective in removal of urine and feces stains.Cuts through food grease fast. With a pH of 11.5 – 12.5, Enz-All is “hot” enough to cut through difficult food grease problems, even the grease that defies high-pressure extraction. When used as a pre-spray, Enz-All will break down the thickest, caked-on kitchen grease or the thinnest body oils with ease.
How to use –
Doubles as a spotter –
Long shelf life –
Kill Odor Plus
Kill Odor Plus is a unique product for the carpet cleaning industry. Three distinct products in one, Kill Odor Plus is a combination of aggressive emulsifiers and surfactants combined with a proprietary odor counteractant specific to modifying the odors associated with urine. KOP is the best choice as a traffic lane pre-conditioner, general purpose spotter and urine odor neutralizer. KOP is also an excellent choice for hard surface restroom clean-up.
Directions for use on carpet:
Always test fabric for colorfastness before applying Kill Odor Plus or any other product. Apply a small amount of cleaner to a clean, white cloth and gently blot test area. If no color transfers to cloth or no change in original fabric occurs, continue with directions below.
Blot and agitate the spotting solution. Allow 5 minutes dwell time then extract or rinse with water.
Heavily Soiled Traffic Lanes
Pre-spray area to be cleaned at a rate of 200 to 400 sq. ft. per gallon, agitate Kill Odor Plus thoroughly into the carpet’s pile, allow 10 minutes of dwell time then extract with an extractor using hot water and DFC 105 in the machine.
Hot Water Extraction Process
Pre-spray area to be cleaned at a rate of 1000 sq. ft. per gallon, agitate Kill Odor Plus thoroughly into the carpet’s pile, allow 10 minutes of dwell time then extract with an extractor using hot water and DFC 105 in the machine.
Use air movers to speed dry the carpet. Make sure the carpet is dry before traffic is allowed on it to prevent rapid re-soiling.
Directions for use in restrooms:
Restoration: mop tile and grout liberally especially around urinals and toilets, allow 10 minutes dwell time then scrub the floor paying particular attention to the areas under and around the urinals and toilets, rinse the floor using a clean damp mop and fresh cold water. Allow the floor to dry before putting the restroom back into service. (More dwell time will be beneficial when strong odors are present, using hot water will intensify the odor problem.)
- Mix 1½-2 qt. (1.5-2.0 L) Fission with enough water to fill
the 5 qt ( 4.7 L) container.
- Use warm water.
Pump-up pressure or electric sprayers:
- Add 4-6 oz. (118-177 mL) of Fission with enough water to make
1 gal. (3.8 L) of RTU solution.
- 1. Pre-inspect / pre-test / pre-treat spots as needed.
- 2. Vacuum the carpet thoroughly.
- 3. Apply Fission RTU solution and allow adequate dwell time.
- 4. Rinse extract with Chemspec Optimal Rinse.
Heavy Duty Soil Lifter
Chemspec Heavy Duty Soil Lifter makes an effective pre-spray for upholstery, draperies, and carpet. Use it with either wet or dry cleaning methods. This one product can perform ALL textile pre-spraying needs.
Heavy Duty Soil Lifter has a special formula comprised of select ingredients that loosen stubborn dirt and oils, making upholstery cleaning easier. It reduces the need for excessive rubbing, which can abrade the fibers of delicate upholstery fabrics.
Heavy Duty Soil Lifter has multiple uses. It can be combined with virtually every wet cleaning detergent system to boost cleaning ability. Not only that, but Heavy Duty Soil Lifter can be used as a spotter for ball point pen ink, grease, oil, or soil filtration lines. It also works as a booster for OMS-based dry cleaning solvents and as a carpet pre-conditioner for heavily soiled olefin carpets.
Heavy Duty Soil LIfter contains no harsh aliphatic or aromatic solvents, so it’s very safe to use. It leaves no sticky residues behind, just a clean, fresh lemon scent that will delight your customers.
Dry Cleaning Upholstery:
Upholstery cleaning is a more delicate cleaning procedure than general carpet cleaning. Upholstery cleaning chemicals are hypoallergenic due to the increased contact with skin. Products used on upholstery must always be tested, even if they are dry solvent products. Do this by having product in the form you would clean with (diluted or undiluted). Look for bleeding, crocking, and color transfer while testing. Check the threading and piping for any abnormalities or different colors. Open up the cushions at the zipper and look for any magic marker used to mark cushions. Common symbols on tags for upholstery are X – vacuum only. S – solvent only, W – wet clean and S/W – solvent or wet clean. Keep in mind sometimes these symbols are referring to the padding instead of the fabric. This is why testing is always recommended.
Dry solvent cleaning of upholstery can be done either by hand or with a dry cleaning machine. Care needs to be taken in using dry cleaning solvents; chemical resistant gloves and other protective equipment should be worn.
Recommended Basic Method:
- Using a viton sealed pump-up sprayer, apply dry solvent pre-spray to upholstery.
- Use a furniture brush to work pre-spray into upholstery.
- Use a viton sealed pump-up sprayer or a dry cleaning machine to apply dry cleaning detergent undiluted to upholstery.
- Agitate with an upholstery brush.
- Dry vacuum with extraction cleaner or use clean white towel to blot dry.
Liquid High Heat
Designed for today’s modern cleaning equipment, Liquid High Heat is a one step cleaning detergent specifically formulated for high heat truck mounts that produce heat in excess of 200 degrees F. Polymer based technology, acid side cleaning eliminates the need for an acid rinse step and encapsulates soil to reduce re-soiling after cleaning.
Cleaning with Liquid High Heat will not cause browning and is completely soluble in hot or cold water. Using Liquid High Heat in your truck mount or portable extractor will neutralize the alkalinity from pre-sprays while you clean. 21st Century cleaning technology, Liquid High Heat contains no dyes, is biodegradable, low VOC and will not clog jets or screens.
When you use Liquid High Heat you experience exceptional cleaning and non re-soiling properties. Liquid High Heat actually encapsulates sticky soils making them easier to remove while you clean and allows vacuuming after cleaning to be more effective and easier.
How acid side cleaning works: While most soils are acid and traditional cleaning methods use alkali detergents to neutralize acid soils for easy removal, acid side detergents work by pushing acid soils away from the fiber. When a cleaning detergent has a negative charge higher than the soil, the soil is pushed away from the carpet and into the solution. When a cleaning detergent has a positive charge higher than the soil, the soil is pulled from the carpet and into the solution.
Directions for use:
Truck mounts – mix 1L to 19L of water for a stock solution or directly feed through your siphon hose. Set your proportion meter to 320:1.
Portable Extractors – mix 60ml to 19 Litres of water.
An oxygen detergent booster additive that whitens and brightens without bleaching. Energizer increases the efficacy of any alkaline cleaning product, enhances colors, deodorizes through chemical modification and saves you time by breaking down tough soils easily.
Energizer makes every alkaline cleaning detergent more powerful. An effective detergent additive. Energizer will boost the cleaning power of any carpet, upholstery, or laundry detergent. The additional cleaning power gives you astounding cleaning results which make your job easier and gives your customers a more pleasing clean. Added power cleaning action begins immediately. No waiting for the extra power. Simply mix Energizer with your cleaning agent, according to directions and begin your power cleaning. Energizer becomes active immediately upon mixing with the cleaning solution to give the added cleaning and color brightening power you want.
Directions for Use:
- Add 3 scoops (3 oz. / 85 g) to 5 gal. (18.9 L) of properly mixed
concentrated detergent stock solution. Stir until mixed.
- 1. Only use when mixed with a detergent.
- 2. Add Energizer just before use as 50% of its strength will exhaust
in 24 hours. To boost effectiveness of leftover solution,
add half of the normal amount of Energizer for the
remaining solution volume.
- 3. Add 1 scoop (1 oz. / 28 g) Energizer to any cleaning solution
to deodorize and oxidize foreign matter and boost cleaning.
***If you do not see a product on our website, check out our store or we can order it!***
For more Chemspec products check out their website: